BloodElf
08-09-2013, 04:43 PM
Lista que uso siempre que me salta BSOD cuando hago OC y pruebo cosas.
BSOD codes for overclocking
0x101 = increase vcore
0x124 = increase/decrease QPI/VTT first, if not increase/decrease vcore...have to test to see which one it is
on i7 45nm, usually means too little VVT/QPI for the speed of Uncore
on i7 32nm SB, usually means too little vCore
0x0A = unstable RAM/IMC, increase QPI first, if that doesn't work increase vcore
0x1A = Memory management error. It usually means a bad stick of Ram. Test with Memtest or whatever you prefer. Try raising your Ram voltage
0x1E = increase vcore
0x3B = increase vcore
0x3D = increase vcore
0xD1 = QPI/VTT, increase/decrease as necessary, can also be unstable Ram, raise Ram voltage
0x9C = QPI/VTT most likely, but increasing vcore has helped in some instances
0x50 = RAM timings/Frequency or uncore multi unstable, increase RAM voltage or adjust QPI/VTT, or lower uncore if you're higher than 2x
0x109 = Not enough or too Much memory voltage
0x116 = Low IOH (NB) voltage, GPU issue (most common when running multi-GPU/overclocking GPU)
0x7E = Corrupted OS file, possibly from overclocking. Run sfc /scannow and chkdsk /r
124 is mostly qpi/vtt but can some times be vcore try qpi/vtt first.
The 0x124
on i7 45nm, usually means too little VVT/QPI for the speed of Uncore.
On i7 32nm SB, usually means too little vCore. I've been getting it specifically when the vCore is too far from the target, but have been getting 0x101 when it was closer.
BSOD 124 on LGA775 platforms means Vcore 90% of the time, but sometimes can be caused by VTT being too high or too low
No es robada no :whistle:
BSOD codes for overclocking
0x101 = increase vcore
0x124 = increase/decrease QPI/VTT first, if not increase/decrease vcore...have to test to see which one it is
on i7 45nm, usually means too little VVT/QPI for the speed of Uncore
on i7 32nm SB, usually means too little vCore
0x0A = unstable RAM/IMC, increase QPI first, if that doesn't work increase vcore
0x1A = Memory management error. It usually means a bad stick of Ram. Test with Memtest or whatever you prefer. Try raising your Ram voltage
0x1E = increase vcore
0x3B = increase vcore
0x3D = increase vcore
0xD1 = QPI/VTT, increase/decrease as necessary, can also be unstable Ram, raise Ram voltage
0x9C = QPI/VTT most likely, but increasing vcore has helped in some instances
0x50 = RAM timings/Frequency or uncore multi unstable, increase RAM voltage or adjust QPI/VTT, or lower uncore if you're higher than 2x
0x109 = Not enough or too Much memory voltage
0x116 = Low IOH (NB) voltage, GPU issue (most common when running multi-GPU/overclocking GPU)
0x7E = Corrupted OS file, possibly from overclocking. Run sfc /scannow and chkdsk /r
124 is mostly qpi/vtt but can some times be vcore try qpi/vtt first.
The 0x124
on i7 45nm, usually means too little VVT/QPI for the speed of Uncore.
On i7 32nm SB, usually means too little vCore. I've been getting it specifically when the vCore is too far from the target, but have been getting 0x101 when it was closer.
BSOD 124 on LGA775 platforms means Vcore 90% of the time, but sometimes can be caused by VTT being too high or too low
No es robada no :whistle: